QC11Y hydraulic guillotine cutting equipment,round bar shears
Basic Info
Model No.: QC11K-6x6000
Product Description
Specifications 1.Omega Hydraulic System
2.SIEMENS electrics
3.linear guideway and ball screws
4.Optional NC/CNC
5.Good price & quality
CNC guillotine shear machine: 1.Frame structure Designed under LVD technology Full steel structure, stress released, with accuracy well kept. Main component is designed and Finite Element Analyzed through ANSYS software. Main frame composes of uprights, working table, holding-down beam and oil tank. Ball transporter and supporting bar and squaring arm are fixed on working table. 2.Upper blade beam and blades Guillotine type blade beam, with rake angle adjustable The rake angle could be motorized adjusted by press button according to material and thickness. When shearing thin thickness sheet, the rake angle could be reduced, thus the distortion of the product and the burr could be minimized. Exchangeable Rectangle blade, with 4 cutting edges available. Blade material 6CrW2Si with hardness HRC53-60, with quality shearing result and long life. 3. Shearing length/stroke adjustment The shearing stroke could be adjusted through knob to the length of the product. Thus efficiency could be improved. 4. Cutting beam guiding and blade clearance The cutting beam is guided between roller guides. At the rear of the cutting beam there are two sets of upper and lower roller guides located at each end of the beam. Two spring-loaded rollers located at the front of the shear apply pressure to the cutting beam, forcing it against the back roller guides. The bearings of the upper roller guides at the back of the cutting beam are mounted on an eccentric shaft. Rotating this shaft causes the cutting beam to tilt, thus providing proper blade clearance to the shearing blades. The upper cutting beam inclined forward, with high section-cutting quality on the product. The blades clearance could be adjusted manually through hand-wheel according to material and thickness. Since the blade clearance is 0.1 to 2.5 mm, the shear can cut thickness 1mm to 40mm mild steel. 5. Hydraulic system LVD special hydraulic unit for heavy type shear is adopted. Hydraulic control components is from VICKERS,USA (or REXROTH, Germany) With in-series cylinders to achieve good synchronization. The sheet is pressed by hold-down before shearing and during shearing for safety and reliability. One-time machining on CNC lathe for cylinder body and piston rod. Horning for inner surface of cylinder, vibration super-fine machining on the outer surface of the piston rod. Oil seals from NOK, Japan (or Merkel, Germany) with low wear and tear, no oil leakage. High-pressure internal gear pump, with reliability and low noise. Over-load protection for hydraulic system 6. Electrical system Movable remote operation station with emergency stop. Main electrical components(contactor, button and switch) adopt product from TELEMECANIQUE from France. Requirement on working condition: Working temperature: -10 to 47 Power supply: 380V±5%, 50HZ, 3 Phase 7. Shadow line lighting It is clear with shadow line lighting for a close and accurate view of the cutting line. 8. Motorized Back gauge The back gauge is driven by lead screw and normal motor. With electrical display, with stroke 1000mm. 9. Safety device Fence guard and protection switch for preventing finger being cut. Movable remote foot pedal with emergency stop 10. Key parts on shear
11.CNC controller:DAC310 and DAC360,DELEM ,Holand,etc.
Contact us if you need more details on Cutting Equipment. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Guillotine Cutting Equipment、Bar Shears. If these products fail to match your need, please contact us and we would like to provide relevant information.
2.SIEMENS electrics
3.linear guideway and ball screws
4.Optional NC/CNC
5.Good price & quality
CNC guillotine shear machine: 1.Frame structure Designed under LVD technology Full steel structure, stress released, with accuracy well kept. Main component is designed and Finite Element Analyzed through ANSYS software. Main frame composes of uprights, working table, holding-down beam and oil tank. Ball transporter and supporting bar and squaring arm are fixed on working table. 2.Upper blade beam and blades Guillotine type blade beam, with rake angle adjustable The rake angle could be motorized adjusted by press button according to material and thickness. When shearing thin thickness sheet, the rake angle could be reduced, thus the distortion of the product and the burr could be minimized. Exchangeable Rectangle blade, with 4 cutting edges available. Blade material 6CrW2Si with hardness HRC53-60, with quality shearing result and long life. 3. Shearing length/stroke adjustment The shearing stroke could be adjusted through knob to the length of the product. Thus efficiency could be improved. 4. Cutting beam guiding and blade clearance The cutting beam is guided between roller guides. At the rear of the cutting beam there are two sets of upper and lower roller guides located at each end of the beam. Two spring-loaded rollers located at the front of the shear apply pressure to the cutting beam, forcing it against the back roller guides. The bearings of the upper roller guides at the back of the cutting beam are mounted on an eccentric shaft. Rotating this shaft causes the cutting beam to tilt, thus providing proper blade clearance to the shearing blades. The upper cutting beam inclined forward, with high section-cutting quality on the product. The blades clearance could be adjusted manually through hand-wheel according to material and thickness. Since the blade clearance is 0.1 to 2.5 mm, the shear can cut thickness 1mm to 40mm mild steel. 5. Hydraulic system LVD special hydraulic unit for heavy type shear is adopted. Hydraulic control components is from VICKERS,USA (or REXROTH, Germany) With in-series cylinders to achieve good synchronization. The sheet is pressed by hold-down before shearing and during shearing for safety and reliability. One-time machining on CNC lathe for cylinder body and piston rod. Horning for inner surface of cylinder, vibration super-fine machining on the outer surface of the piston rod. Oil seals from NOK, Japan (or Merkel, Germany) with low wear and tear, no oil leakage. High-pressure internal gear pump, with reliability and low noise. Over-load protection for hydraulic system 6. Electrical system Movable remote operation station with emergency stop. Main electrical components(contactor, button and switch) adopt product from TELEMECANIQUE from France. Requirement on working condition: Working temperature: -10 to 47 Power supply: 380V±5%, 50HZ, 3 Phase 7. Shadow line lighting It is clear with shadow line lighting for a close and accurate view of the cutting line. 8. Motorized Back gauge The back gauge is driven by lead screw and normal motor. With electrical display, with stroke 1000mm. 9. Safety device Fence guard and protection switch for preventing finger being cut. Movable remote foot pedal with emergency stop 10. Key parts on shear
No. | Item | Brand | Origin |
1 | Pump | NACHI | Japan |
2 | Hydraulic valve | REXROTH | Germany |
3 | Seals | NOK | Japan |
4 | Main electrical parts | TELEMECANIQUE | France |
5 | Encoder | ELTRA | Italy |
6 | Filter | COMPASS | Taiwan, China |
7 | Main motor | ABB | China |
8 | Electrical display | KUBLER | Germany |
Hydraulic guillotine shear (Series QC11Y) | ||||||||
Model | Maximum Shear thickness mm | Maximum shear width mm | Shear angle ° | Plate strength n/m2 | Back-gauge station mm | Main motor kw | Dimension (LXWXH) mm | Weight kg |
QC11Y-8X4000 | 8 | 4000 | 0.5°-2° | 450 | 800 | 11 | 4620X1800X2050 | 9500 |
QC11Y-12X2500 | 12 | 2500 | 0.5°-2.5° | 450 | 1000 | 18.5 | 3180X1800X2100 | 8200 |
QC11Y-12X3200 | 12 | 3200 | 0.5°-2.5° | 450 | 1000 | 18.5 | 3980X1950X2310 | 11800 |
QC11Y-12X4000 | 12 | 4000 | 0.5°-2.5° | 450 | 1000 | 18.5 | 4780X2000X2400 | 15500 |
QC11Y-12X6000 | 12 | 6000 | 0.5°-2.5° | 450 | 1000 | 30 | 6800X2500X2950 | 28000 |
QC11Y-16X2500 | 16 | 2500 | 0.5°-2.5° | 450 | 1000 | 22 | 3280X1900X220 | 10000 |
QC11Y-16X3200 | 16 | 3200 | 0.5°-2.5° | 450 | 1000 | 22 | 3980X2000X2425 | 13500 |
QC11Y-16X4000 | 16 | 4000 | 0.5°-2.5° | 450 | 1000 | 22 | 4780X2200X2520 | 17800 |
QC11Y-16X6000 | 16 | 6000 | 0.5°-2.5° | 450 | 1000 | 30 | 6800X2600X3050 | 35000 |
QC11Y-20X2500 | 20 | 2500 | 0.5°-2.5° | 450 | 1000 | 30 | 3300X2000X2380 | 14000 |
QC11Y-20X3200 | 20 | 3200 | 0.5°-2.5° | 450 | 1000 | 30 | 4000X2280X2490 | 17000 |
QC11Y-20X4000 | 20 | 4000 | 0.5°-2.5° | 450 | 1000 | 30 | 4800X2500X3000 | 28000 |
QC11Y-25X2500 | 25 | 2500 | 0.5°-2.5° | 450 | 1000 | 37 | 3400X2300X2750 | 19000 |
QC11Y-25X3200 | 25 | 3200 | 0.5°-2.5° | 450 | 1000 | 37 | 4100X2400X2580 | 24000 |
QC11Y-32X2500 | 32 | 2500 | 0.5°-3° | 450 | 1000 | 37 | 3400X2400X2850 | 22000 |
QC11Y-32X3200 | 32 | 3200 | 0.5°-3° | 450 | 1000 | 37 | 4100X2550X3000 | 28000 |
QC11Y-40X2500 | 40 | 2500 | 1°-3.5° | 450 | 1000 |
Product Categories : shearing machine & cutting machine > CNC guillotine shearing machine
Premium Related Products
Other Products
Hot Products
Four Column Hydraulic Press (TT-SZ40T)1000tons/2000t Hydraulic Deep Drawing Press (TT-LM1000T-2000T)CE/Nr Standard Hydraulic Press Machine (TT-LM4000T)pneumatic press punching machine made in chinacnc amada hydraulic bending press brake machine bender60Tons C Frame Four-guide Single Column CNC Hydraulic Press Machinehot sale steel door hydraulic press machine pricesheet metal folder 5m, press brake 5miron sheet hydraulic guillotine shear machine 4mFactory Price Metal Cutting Machine / Hydraulic Shearing Machine 6x2500aluminium foil pan press machine 45tons with two cavityWE67Y metal plate press brake bender machineMetal Pipe Tube Embossing Machine Swaging Machine100w 150w 300w 500w cnc plasma laser cutting engraving machineHydraulic salt lick block pressing machine,cow salt licking brick making machineconstruction building diesel engine manual cement concrete hollow block brick making machine